Class I+ Class II / Type 1+ Type 2 Protection Device Protection Surge Protection (SPD)

Prosurge’s Type 1 + Type 2 دستگاه های حفاظت در برابر سرریز (SPDs) are designed to discharge high current surges without any destruction of the installation.

This surge protective device is characterized by its capacity to withstand impulse current with 10/350µs waveform which simulates direct impact coming from a natural lightning current.

Prosurge Type 1 + Type 2 (class I + Class II)  SPDs are placed at the entrance point of the installation, in the main distribution board for a global protection of this installation.

Prosurge also provides Class I + Class II, Type 1 + Type 2 SPD with different technology of spark gap technology, VT technology and MOV technology.

Class-1-2-Type-1-2-SPD_triggered-spark-gap-technology-Prosurge-258×212

فناوری MOV -12.5kA 10/350 – دارای گواهینامه TUV

Class-1-2-Type-1-2-SPD_triggered-spark-gap-technology-Prosurge-258×212

فناوری MOV - 25kA 10/350 - دارای گواهینامه TUV

Class-1-2-Type-1-2-SPD_triggered-spark-gap-technology-Prosurge-258×212

Class II / Type 2 (also tested to class I + Class II, T1 +T2) Surge Protection Device (SPD)

Prosurge Type 2 دستگاه های حفاظت در برابر سرریز (SPDs) are also tested to Type 1 + Type 2 with impulse current 10/350µs.

It is designed to discharge high current surges without any destruction of the installation. This surge protective device is characterized by its capacity to withstand impulse current with 10/350µs waveform which simulates direct impact coming from a natural lightning current. Prosurge Type 2 SPD (also T1 + T2) SPDs are placed at the entrance point of the installation, in the main distribution board for a global protection of this installation.

رتبه:

  • Uc range: 75Vac to 750Vac
  • Imax: 50kA 8/20
  • Iimp: 7.5kA 10/350
  • Various SPD configuration: 1+1, 2+0, 3+0, 3+1 SPD

دستگاه حفاظتی فوق العاده کلاس II / نوع 2 (SPD)

Prosurge Class II/T2 surge protective device is designed for low-voltage power supply system protection against surges at the boundaries from lightning protection zone 1-2 and higher.

  • KEMA certified Class II/T2 SPD per IEC/EN 61643-11.
  • UL certified Type 1ca SPD per UL1449 5th edition (pass SCCR test 200kArms)
  • ظرفیت تخلیه جریان بالا تا 40kA 8 / 20μs
  • High reliability due to global patented thermally protected MOV with reliable arc-extinguish (TPAE) technology.
  • ماژول قابل جابجایی برای جایگزینی آسان
  • Degradation indication and remote signal contact.
  • Comply with IEC/EN 61643-11, UL1449 5th, CSA C22.2 etc standards

دستگاه محافظت در برابر فشار کلاس III / نوع 3 (SPD)

Prosurge T3 Surge Protection Device (SPD) is designed for low-voltage power supply system protection against surges at the boundaries from lightning protection zone 2-3 and higher.

برای محافظت باید از نزدیک در نزدیکی تجهیزات حساس نصب شوند. آنها با یک مولد موج ترکیبی جریان 1,2،50 / 8 - 20/XNUMX آزمایش شده اند ، از مقدار ولتاژ سطح حفاظت بسیار پایین اطمینان می دهند.

  • Comply with IEC 61643-11 and UL1449 5th
  • طراحی قابل انعطاف، آسان بدون هر گونه ابزار جایگزین.
  • High Discharge Capacity with 8/20 us waveform, Imax 10kA to 25kA 8/20
  • قابلیت اطمینان بالا به دلیل دستگاه قطع کننده حرارتی
  • نماد وضعیت ویژوال و تماس سیگنال از راه دور در دسترس است
  • Mono block type for single phase and three phase configuration are available

PCB Mounting SPD – Pluggable while install with soldering socket

The PCB mounting surge protective device is easy untegrated in PCB and close to sensitive electronic element inside device, to minimize the potential impact of lightning events. The PCB mounting SPD will help to significantly reduce the cost of substantial repair, replacement, system downtime and the loss of revenue.

Prosurge’s PCB mounting SPD is size optimization and space efficiency, which is a high performance but low cost solution for the industry of power electronics. It employs high energy Metal Oxide Varistor (MOV), and constructed with patented thermal protection and arc extinguishing technology which ensure safe disconnection while faulty current or abnormal voltage happened. Prosurge PCB mounting SPDs have comprehensively improved the safety performance and proven to be excellent fail-safe and self-protected protective devices because of patented technology.

  • رتبه:
    • برای برنامه AC: حداکثر. ولتاژ کار مداوم (MCOV): 75~750Vac
    • برای کاربرد DC/PV: حداکثر. ولتاژ مجاز DC (Vpvdc): 48-825Vdc
    • Surge capacity (8/20 μs):50kA ~ 80kA
    • Impulse current (10/350 μs): 7.5kA ~ 12.5kA
    • SCCR(UL1449 5th):up to 200kA – tested without external CB or fuse
    • Iscpv (IEC61643-31):1000A
  • شناسایی UL نوع 1ca SPD (ANSI/UL1449 چهارم)، نوع 5ca SPD (CSA-C2)
  • TUV certified as per IEC 61643-31 standard
  • واکنش سریع حرارتی و عملکرد کامل قطع مدار به علت طراحی خاص جدا کننده حرارتی با دستگاه خاموش کردن قوس
  • محدوده دمای کاری و قابلیت اطمینان بالا
  • ظرفیت جریان بالا بالا و جریان نشت کم
  • تماس سیگنالینگ از راه دور برای نشان دادن خطا در حالی که استفاده های دیگر از PVD_Base است

Prosurger Surge Protection Device Products Family

کلیک کنید برای کشف دستگاه های حفاظتی گسترده خود و دیگر محصولات حفاظت از رعد و برق.

SPD برای سیستم اطلاعاتی

SPD برای اترنت

SPD for datalines (UL497b)

SPD برای ویدیو

SPD برای کواکسیال

دیگر محصولات حفاظت از ریزش و رعد و برق

ضد انفجار

مانیتور خروجی

پیوند احتمالی رعد و برق

Prosurger Surge Protection Device Products Family

کلیک کنید برای کشف دستگاه های حفاظتی گسترده خود و دیگر محصولات حفاظت از رعد و برق.

با Prosurge تماس بگیرید و در 2 ساعت پاسخ دهید

ببینید که چگونه قیمت ما رقابتی است:)

با کلیک بر روی دکمه چت در گوشه سمت راست پایین، با ما تماس بگیرید

فرم تماس را پر کنید و پاسخ در ساعت 2 دریافت کنید





برای بازار آمریکای شمالی، لطفا با ما تماس بگیرید

۴۴۲۰۳۰۹۵۷۲۹۲+

برای سایر بازارهای، لطفا با ما تماس بگیرید

۴۴۲۰۳۰۹۵۷۲۹۲+