I+ klass II klass / tüüp 1+ tüüp 2 liigpingekaitseseade (SPD)

Prosurge’s Type 1 + Type 2 Ülepinge kaitseseadmed (SPDs) are designed to discharge high current surges without any destruction of the installation.

This surge protective device is characterized by its capacity to withstand impulse current with 10/350µs waveform which simulates direct impact coming from a natural lightning current.

Prosurge Type 1 + Type 2 (class I + Class II)  SPDs are placed at the entrance point of the installation, in the main distribution board for a global protection of this installation.

Prosurge also provides Class I + Class II, Type 1 + Type 2 SPD with different technology of spark gap technology, VT technology and MOV technology.

Class-1-2-Type-1-2-SPD_triggered-spark-gap-technology-Prosurge-258×212

MOV tehnoloogia -12.5 kA 10/350 – TUV sertifikaat

Class-1-2-Type-1-2-SPD_triggered-spark-gap-technology-Prosurge-258×212

MOV tehnoloogia – 25kA 10/350 – TUV sertifikaat

Class-1-2-Type-1-2-SPD_triggered-spark-gap-technology-Prosurge-258×212

Class II / Type 2 (also tested to class I + Class II, T1 +T2) Surge Protection Device (SPD)

Prosurge Type 2 Ülepinge kaitseseadmed (SPDs) are also tested to Type 1 + Type 2 with impulse current 10/350µs.

It is designed to discharge high current surges without any destruction of the installation. This surge protective device is characterized by its capacity to withstand impulse current with 10/350µs waveform which simulates direct impact coming from a natural lightning current. Prosurge Type 2 SPD (also T1 + T2) SPDs are placed at the entrance point of the installation, in the main distribution board for a global protection of this installation.

Hinnang:

  • Uc range: 75Vac to 750Vac
  • Imax: 50kA 8/20
  • Iimp: 7.5kA 10/350
  • Various SPD configuration: 1+1, 2+0, 3+0, 3+1 SPD

II klassi / 2i liigpingekaitseseade (SPD)

Prosurge Class II/T2 surge protective device is designed for low-voltage power supply system protection against surges at the boundaries from lightning protection zone 1-2 and higher.

  • KEMA certified Class II/T2 SPD per IEC/EN 61643-11.
  • UL certified Type 1ca SPD per UL1449 5th edition (pass SCCR test 200kArms)
  • Suur voolutugevuse tühjenemise võimsus kuni 40kA 8 / 20μs
  • High reliability due to global patented thermally protected MOV with reliable arc-extinguish (TPAE) technology.
  • Plussmoodul lihtsaks asendamiseks
  • Degradation indication and remote signal contact.
  • Comply with IEC/EN 61643-11, UL1449 5th, CSA C22.2 etc standards

III klassi / 3. tüüpi ülepingekaitseseade (SPD)

Prosurge T3 Surge Protection Device (SPD) is designed for low-voltage power supply system protection against surges at the boundaries from lightning protection zone 2-3 and higher.

Kaitsmiseks tuleb need paigaldada tundlikest seadmetest võimalikult lähedale. Testitud 1,2 / 50 - 8/20 voolu kombinatsioonlaine generaatoriga tagavad need väga madala kaitsetaseme pinge väärtuse.

  • Comply with IEC 61643-11 and UL1449 5th
  • Planeeritav disain, lihtne asendada ilma igasuguste tööriistadeta.
  • High Discharge Capacity with 8/20 us waveform, Imax 10kA to 25kA 8/20
  • Kõrge töökindlus termilise lahtiühenduse tõttu
  • Visuaalse oleku näidik ja kaugside signaali kontakt on saadaval
  • Mono block type for single phase and three phase configuration are available

PCB Mounting SPD – Pluggable while install with soldering socket

The PCB mounting surge protective device is easy untegrated in PCB and close to sensitive electronic element inside device, to minimize the potential impact of lightning events. The PCB mounting SPD will help to significantly reduce the cost of substantial repair, replacement, system downtime and the loss of revenue.

Prosurge’s PCB mounting SPD is size optimization and space efficiency, which is a high performance but low cost solution for the industry of power electronics. It employs high energy Metal Oxide Varistor (MOV), and constructed with patented thermal protection and arc extinguishing technology which ensure safe disconnection while faulty current or abnormal voltage happened. Prosurge PCB mounting SPDs have comprehensively improved the safety performance and proven to be excellent fail-safe and self-protected protective devices because of patented technology.

  • Hinnang:
    • Vahelduvvoolurakenduse jaoks: Max. Pidev tööpinge (MCOV): 75~750Vac
    • DC/PV rakenduse jaoks: Max. Lubatud alalispinge (Vpvdc): 48-825Vdc
    • Surge capacity (8/20 μs):50kA ~ 80kA
    • Impulse current (10/350 μs): 7.5kA ~ 12.5kA
    • SCCR(UL1449 5th):up to 200kA – tested without external CB or fuse
    • Iscpv (IEC61643-31):1000A
  • UL tunnustatud tüüp 1ca SPD (ANSI/UL1449 5th), tüüp 2ca SPD (CSA-C22.2 )
  • TUV certified as per IEC 61643-31 standard
  • Kiirküttevõimendus ja täiuslik ahela katkestusfunktsioon, mis on tingitud kaar-kustutamisseadmest koosneva termilise lahtilüliti konstruktsiooniga
  • Lai töötemperatuuri vahemik ja kõrge töökindlus
  • Suur voolutugevus ja väike lekkevool
  • Ujuv kaugjuhitav signaalikontakt rikke kuvamiseks PVD_Base'i täiendavate kasutusviiside korral

Prosurge Surge Protection Device tooteperekond

Klõpsake, et uurida meie ulatuslikke ülepingekaitseseadmeid ja teisi välkkaitsevahendeid.

Võtke ühendust Prosurge'iga ja saate vastuse 2 tunni jooksul

vaata, kuidas meie hind on konkurentsivõimeline:)

Otseülekanne meiega, klõpsates paremas nurgas asuvat vestlusnuppu

Täitke 2 tundides kontaktvormi ja saad vastuse





Põhja-Ameerika turul pöörduge palun

+ 86 757 8632 7660

Teiste turgude puhul võtke palun ühendust

+ 86 757 8632 7660